MEMS Exchange (MX)

The summary for the MEMS Exchange (MX) grant is detailed below. This summary states who is eligible for the grant, how much grant money will be awarded, current and past deadlines, Catalog of Federal Domestic Assistance (CFDA) numbers, and a sampling of similar government grants. Verify the accuracy of the data FederalGrants.com provides by visiting the webpage noted in the Link to Full Announcement section or by contacting the appropriate person listed as the Grant Announcement Contact. If any section is incomplete, please visit the website for the Defense Advanced Research Projects Agency, which is the U.S. government agency offering this grant.
MEMS Exchange (MX): Defense Advanced Research Projects Agency (DARPA), Contracts Management Office (CMO), 3701 North Fairfax Drive, Arlington, VA 22203-1714.A - MEMS EXCHANGE (MX), SOL BAA 04-10, DUE 020904, POC CLARK T.-C. NGUYEN, DARPA/MTO, FAX (703) 696-2206 PROGRAM OBJECTIVES AND DESCRIPTIONThe Defense Advanced Research Projects Agency (DARPA) is soliciting research proposals in the area of MEMS Exchange (MX). Proposed research should investigate innovative approaches that enable revolutionary advances in science, devices or systems. Specifically excluded is research which primarily results in evolutionary improvement to the existing state of practice.DARPA is soliciting innovative proposals in the area of microelectromechanical systems (MEMS) process module additions to the MEMS Exchange distributed fabrication network, with the intention of furthering the MEMS Exchange (MX) program goal of providing flexible access to complex MEMS fabrication technology in a wide variety of materials and to a broad multi-disciplinary user base, pursuant to making possible novel devices otherwise unattainable via inflexible foundries. Although complete, self-contained, multi-mask process modules that can serve as "standard" processes are of most interest, single process steps (e.g., a film deposition, an etch capability) will still be considered if exceptionally novel and compelling. Emphasis will be given to multi-mask process modules that are amenable to combination with other modules to yield fully integrated microsystems. Among the relevant set of technologies deemed beneficial to the MEMS Exchange service are: (1) generic, widely-applicable, standard processes-e.g., surface-micromachining, Silicon On Insulator (SOI) micromachining, metal micromachining, etc.-that yield fully functional MEMS devices; (2) process technologies that yield 3-dimensional structures; and (3) generally applicable technologies capable of packaging MEMS devices under environments suitable for optimum performance. Given that one of the main objectives of the MEMS Exchange program is to insure self-sustained operation of the MEMS Exchange service beyond the end of the program, additional consideration will likely be given to process modules perceived to be in highest demand or capable of satisfying a crucial need by any of the DARPA MEMS programs.One of the drivers behind the interest in self-contained, multi-mask process modules is to see if a "standard" MEMS process flow can be identified that is general enough to be used by the majority of MEMS designers in a given class, yet still capable of attaining performance on par with or approaching that of a fully custom process. Such a "universal" MEMS process (or a set of them, one for each "class"), if even possible, would be highly beneficial to the MEMS community, since its ability to support a large number of products could substantially raise the volume of wafers processed per month, thereby greatly lowering the cost of the process, and thus, of the products it services. In essence, such a process might allow the MEMS industry to enjoy the same standardization advantages that the extremely high volume integrated circuit industry presently enjoys. MEMS devices that harness the material and process flexibility provided by the MEMS Exchange distributed fabrication network are expected to enable a myriad of strategic capabilities. In particular, Micro Electro Mechanical Systems (MEMS) technology, with its ability to reduce both size and power consumption in a myriad of sensor, communication, actuation, and information processing devices, has been identified as a key enabling technology for military platforms in all areas. Among the many examples of high payoff applications of MEMS technologies are micromechanical logic circuits for munitions safe-and-arming devices, micromechanical vibrating resonators for frequency selection and generation in miniaturized communication transceivers, programmable micromechanical gratings for remote toxic gas sensors, movable micromirrors for optical switching, micro fuel cells and engines for portable, long-lasting power generation, and chip-scale atomic clocks for portable GPS and ultra-secure communications. The most recent advancements in MEMS technology have invariably required participation from researchers from a widely diverse set of backgrounds, many of whom do not have access to the full spectrum of MEMS technologies. In allowing and encouraging the use of a wide variety of materials and fabrication processes by a broad multi-disciplinary user base, the development and enhancement of the MEMS Exchange should prove instrumental in providing the accessibility to MEMS technology required for a myriad of present and future MEMS-enabled devices for military platforms. In addition, MEMS Exchange can serve as a much-needed fabrication infrastructure for low or medium volume production of MEMS-enabled products for DoD applications.DARPA strongly encourages well-coordinated, interdisciplinary research and development activities that take into consideration all significant and relevant engineering tradeoffs and optimizations. Teaming among academic, industrial and/or government partners is encouraged, and it is anticipated that the contributions of the team members are complementary as well as essential to the critical path of the research plan. Such teaming, however, is not required, and offerings from compelling individual efforts will be given the same consideration as that for teams. A technology insertion plan is encouraged and research that holds promise of insertion into Department of Defense (DoD) relevance is of great interest.Additional information on these technology areas is provided in the Areas of Interest section of the BAA 04-10 Proposer Information Pamphlet referenced below.PROGRAM SCOPEThis addition to the MEMS Exchange program is meant to support short-term efforts, on the order of one year or less, that should culminate in the insertion of new process modules into the MEMS Exchange service that greatly enhance its overall capability and increase its user base. Several awards in amounts ranging from $100,000 to $200,000, and all totaling $1 million, are expected to be made during the second quarter of fiscal year 2004. A web site-http://teaming.sysplan.com/BAA-04-10/ has been established to facilitate formation of teaming arrangements between interested parties. Specific content, communications, networking, and team formation are the sole responsibility of the participants. Neither DARPA nor the Department of Defense (DoD) endorses the destination web site or the information and organizations contained therein, nor does DARPA or the DoD exercise any responsibility at the destination. This web site is provided consistent with the stated purpose of this BAA. Cost sharing is not required and is not an evaluation criterion, but is encouraged where there is a reasonable probability of a potential commercial application related to the proposed research and development effort. Questions concerning this BAA may be directed to the technical POC for this effort, Dr. Clark T.-C. Nguyen, phone: (571) 218-4586, fax: (703) 696-2206, electronic mail: [email protected] INFORMATIONProposers must obtain a pamphlet entitled "BAA 04-10, MEMS Exchange, Proposer Information Pamphlet" which provides further information on MEMS Exchange, the submission, evaluation, and funding processes, proposal formats, and other general information. This pamphlet may be obtained from the FedBizOpps website: http://www.fedbizopps.gov/, World Wide Web (WWW) at URL http://www.darpa.mil/ or by fax, electronic mail, or mail request to the administrative contact address given below. Proposals not meeting the format described in the pamphlet may not be reviewed. Proposers must submit an original and seven (7) copies of the proposal and two electronic copies (i.e., two separate disks) of the proposal (in PDF - preferred, MS-Word readable, HTML, or ASCII format, each on a single 3.5 inch High Density MS-DOS formatted 1.44 Megabyte (MB) diskette, a single 100 MB Iomega Zip disk, or a CD-ROM). Also include on each disk the one-slide PowerPoint file summarizing your proposal, as described under the Proposal Format sub-section of Section I of this BAA. Each disk must be clearly labeled with BAA 04-10, proposer organization, proposal title (short title recommended) and Copy __ of 2. The proposal (original and designated number of hard and electronic copies) must be submitted to DARPA/MTO, 3701 North Fairfax Drive, Arlington, VA 22203-1714 (Attn.: BAA 04-10), and must be received by DARPA on or before 4:00 P.M., local time, Monday, February 9, 2004, in order to be considered during the initial round of selections; however, proposals received after this deadline may be received and evaluated up to one year from date of posting on FedBizOpps. Proposals submitted after the due date specified in the BAA may be selected contingent upon the availability of funds. This notice, in conjunction with the BAA 04-10 Proposer Information Pamphlet, constitutes the total BAA. No additional information is available, nor will a formal RFP or other solicitation regarding this announcement be issued. Requests for the same will be disregarded. The Government reserves the right to select for award all, some, or none of the proposals received. All responsible sources capable of satisfying the Government's needs may submit a proposal which shall be considered by DARPA. Input on technical aspects of the proposals may be solicited by DARPA from non-Government consultants/experts who are bound by appropriate non-disclosure requirements. Non-Government technical consultants/experts will not have access to proposals that are labeled by their offerors as "Government Only". Historically Black Colleges and Universities (HBCUs) and Minority Institutions (MIs) are encouraged to submit proposals and join others in submitting proposals; however, no portion of this BAA will be set aside for HBCU and MI participation due to the impracticality of reserving discrete or severable areas of research in MEMS Exchange. All administrative correspondence and questions on this solicitation, including requests for information on how to submit a proposal to this BAA, should be directed to one of the administrative addresses below; e-mail or fax is preferred. DARPA intends to use electronic mail and fax for correspondence regarding BAA 04-10. Proposals may not be submitted by fax or e-mail; any so sent will be disregarded. DARPA encourages use of the WWW for retrieving the Proposer Information Pamphlet and any other related information that may subsequently be provided.EVALUATION CRITERIAEvaluation of proposals will be accomplished through a technical review of each proposal using the following criteria, which are listed in descending order of relative importance: (l) overall scientific and technical merit, (2) potential contribution and relevance to DARPA mission, (3) plans and capability to accomplish technology transition, (4) offeror's capabilities and related experience, and (5) cost realism. Note: cost realism will only be significant in proposals which have significantly under or over-estimated the cost to complete their effort. The administrative addresses for this BAA are:Fax: (703) 351-8616 (Addressed to: DARPA/MTO, BAA 04-10), Electronic Mail: [email protected]: DARPA/MTO, ATTN: BAA 04-10 3701 North Fairfax Drive Arlington, VA 22203-1714 This announcement and the Proposer Information Pamphlet may be retrieved via the WWW at URL http://www.darpa.mil/ in the solicitations area.
Federal Grant Title: MEMS Exchange (MX)
Federal Agency Name: Defense Advanced Research Projects Agency
Grant Categories: Science and Technology
Type of Opportunity: Discretionary
Funding Opportunity Number: BAA04-10
Type of Funding: Other Grant Cooperative Agreement
CFDA Numbers: 12.910
CFDA Descriptions: Research and Technology Development
Current Application Deadline: No deadline provided
Original Application Deadline: Feb 09, 2004
Posted Date: Dec 19, 2003
Creation Date: Aug 14, 2006
Archive Date: Aug 15, 2006
Total Program Funding:
Maximum Federal Grant Award: $0
Minimum Federal Grant Award: $0
Expected Number of Awards:
Cost Sharing or Matching: No
Applicants Eligible for this Grant
Unrestricted (i.e., open to any type of entity above), subject to any clarification in text field entitled "Additional Information on Eligibility"
Grant Announcement Contact
Schoen, Jennifer, Contracting Officer, Phone 703 696-2440, Fax 703-741-0602, Email [email protected] [email protected] Schoen, Jennifer
Similar Government Grants
Material Synthesis Technologies for Universal and Diverse Integration Opportunities (M-STU...
Scientific Feasibility (SciFy)
Expeditionary Carbon Utilization for energy Resilience and Stabilization (ExCURSion)
BioLogical Undersea Energy (BLUE)
Young Faculty Award (YFA) 2024
Wide Band Gap Semiconductors for RF Applications (WBGS-RF)
Robust Integrated Power Electronics (RIPE)
Microantenna Arrays:Technology and Applications (MIATA)
More Grants from the Defense Advanced Research Projects Agency
Biological Technologies
Mining and Understanding Software Enclaves (MUSE)
Big Mechanism
DARPA-BAA-13-11: Vetting Commodity IT Software and Firmware
Microsystems Technology Office-Wide

FederalGrants.com is not endorsed by, or affiliated with, any government agency. Copyright ©2007-2024 FederalGrants.com